
企業新聞 品牌專欄 案例報道 企業文化 技術文章 產品評測
2015年04月19日 18:35東臺市東方船舶裝配有限公司 業安點擊量:2308
本產品RDF400角雷達反射器是配備于救生艇,救生筏。為增強小雷達目標回波的全向無源裝置,它由每個導電平面互相垂直交叉而構成,平行于入射方向反射入射波的較大部分。其性能符合標準化組織ISO8729:1997{E}的技術要求及海事組織IMO決議A-384{X}決議的規定。
主要技術指標:
1:反射面積 大于40M2 2:總重量為 小于1.6公斤
本產品有船檢CCS證書!
此款產品的安裝方法:
一、將反射器從包裝袋中取出,將導電片圍繞不銹鋼轉動軸展開向下、上8個直角三角形,而后將導簧銷對準橢圓潤孔插入再旋轉90°鎖住。
Take reflection equippment out o packing bag.make the conducting flake surround the stainless steel rctating axis and outspread as 8 right-angle triangle up and down,then insert the spring pin into the ellpse hole and then screw by 90 °to lock(See picture 3、4&5)
二、將不銹鋼轉動軸中心內的一根不銹鋼支桿拔出約20公分然后將塑料固定螺栓螺母旋緊。
(2)Pull out a stainless beanpcle in the center of the stainless steel rotating axis by 20cm.then screwlight lastic bolt&nut(See picture 6)
三、將連接在反射器上的20公分支桿從救生艇筏頂蓬洞孔中插入閥體內,然后在筏體內再將其插入不銹鋼升降支架中,zui后將升降支架上的全部塑料螺栓旋緊與筏低固定好即可。
(3)Inset the 20cm long beanpole connected to refletion equippment to the hole on top sail of the raft,then insert it to the stainless steel up-and-down bracket in the body of the raft,at last screw tight all the plastic bolt & nut. make sure they firmly fixed to the bottom of the raft.(See picture 7)
四、建議安裝高度:水平面2m
Propositonal installation height:2m from level
五、注意事項:Notice
(1)安裝方法:避免陰影區。Installation Method:To avoid the shadoe area.
(2)羅盤的安全距離:2m。 Sfety Distance of Compass:2m.
本網轉載并注明自其它來源(非智慧城市網www.duty-free.cn)的作品,目的在于傳遞更多信息,并不代表本網贊同其觀點或和對其真實性負責,不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時,必須保留本網注明的作品第一來源,并自負版權等法律責任。