IBH 10018 德國Windows®7版的S5 IBH softec
IBH 10018 德國Windows®7版的S5 IBH softec
歡迎各位商友洽談咨詢：
穆澤工業控制系統（上海）有限公司
銷售工程師：蔣成功
騰訊：528394876
手機：139*1670*9240（去除"*"）(wx同號）
E-mail:gcg#morzor。com（將"#"替換為"@"，"。"替換為".")
德國全新* IBH softec，德國法蘭克福機場直飛。
提供IBH softec 客戶端模塊/軟件/以太網模塊/適配 等經濟高效的替代解決方案。
另：
我司專業·銷售·德國·菲尼克斯(phoenix contact)產品：中間繼電器、安全繼電器、變送器、隔離器、驅動器、傳感器、執行器、防雷器、光電耦合器、開關電源、現場I/O系統、模塊、網絡接口、連接器、工業交換機、工業無線產品、通迅產品、監視器、保護器、打印機、工具、接線端子等
版本7的新功能：
- OsziCam®
- 狀態記錄器
- 日志查看
- 智能輸入?yún)f(xié)助
- 通過SINEC L2在線連接到SIMATIC S5
- 通過H1在線連接到SIMATIC S5
- 在
Windows XP（32/64位）
Windows Vista（32/64位）
Windows 7（32/64位）
Windows 8（32/64位）
Windows 10（32/64位）上調用STEP5 COM軟件包
Windows®S5提供了用于創建，修改，測試和記錄可編程邏輯控制器（PLC）程序的工具。Windows®S5專為使用STEP5對Siemens PLC系列SIMATIC S5進行編程而設計。功能塊圖（FBD），梯形圖（LAD）和語句列表（STL）用作S5的演示。可以直接編輯現有的S5程序，而無需導入/導出。Windows®的S5與原始的Siemens編程單元兼容。為了自動進行故障排除，還集成了S5 Doctor功能。
OsciCAM®允許通過同步先前記錄的視頻和過程信號來分析運動過程。記錄的視頻可與過程信號同步顯示，并帶有時間戳顯示PLC的已記錄塊狀態。
With the Statusrecorder, dynamic procedures can be expolored by subsequently analysis of the block status frame by frame. The Statusrecorder logs the block status and shows these with time stamp, permitting subsequent changing between the presentations STL, CSF and LAD.
With the Oscilloscope feature the diagnostic capabilities of the programming system are further enhanced. Dynamic processes can be monitored and analyzed in an integrated screen, in look and feel adapted from an oscilloscope front panel. Pointing to I/O signals with a virtual test probe is sufficient for monitoring multiple signals inside the virtual oscilloscope. Signal recording can be stopped at any time for further timing investigation of the machine fault. Besides watching I/O signals, also the state of local variables at a defined position of program execution can be watched, by simply pointing to the variable with the test probe in block status. Only the integration into the programming system S5 for Windows® makes this possible. The recorded data can also be saved for later investigation, for archiving purposes or to send the information via e-mail.
A comfortable editor to create and edit symbolic tables is integrated. Searching and replacing for any criteria as well as rewiring is possible. A syntax check is integrated. The new comfortable multiple segment editor for the creation of statement lists, function block diagrams and ladder diagrams allows the representation of complex functions too. Focus was set on the ease of use with the mouse and/or the keyboard. Cross references and/or the corresponding symbol files are shown with the correct addresses. In this window the symbol file can be edited simultaneously. The allocation
of new addresses with syntax check is integrated. Statement lists are created with the comfort of integrated editor. The Windows clipboard can be used for program or configuration manipulations in any place. Statement lists can be altered into function block diagram or ladder diagrams, as far as they are displayable. The display of Function Block Diagrams and Ladder Diagrams in form of State Statement Lists is always possible.
With S5 for Windows® multiple segments can be shown in the status display representations statement list, function block diagram and ladder diagram. The CPU status function provides information about interrupt stack, block stack and system data.
S5 for Windows® allows calling the COM packages. Communication to a PLC can be established via an USB adaptor. This function is suppoertd with the operating systems Windows 2000 and WindowsXP(32 Bit) only.
The G5 for Windows® Step Sequence Programming (now included within S5 for Windows®) is a tool for easy programming sequential steps (sequencer control) within a STEP5 PLC program. A Step Sequence programmed in a Step Sequence Block (SB) is made out of steps and transitions. The transitions logic is used to enable the following step.
The graphical G5 for Windows® Step Sequence Programming supports linear sequences, alternative branching, simultaneous branching and jumps. Steps are displayed with boxes. There is a differentiation between an initial step, a permanent step, and a selective step. The initial step is used for an unconditional start of the Step Sequence. The instructions of a permanent step will always be executed even if the step flag is not active. The instructions of a selective step will be jumped over if the step flag is not active.Transitions are displayed as lines. The following step will only be executed if the logic of a transition is true. With a simultaneous branch it is possible to branch up to eight (8) further steps. The graphical display of steps and transitions may include comments. With the exception of the initial step, each step may be assigned to a time. This could be a waiting time (delay timer) or a monitoring time (watch dog).
用于Windows®圖形步驟序列的G5與SIEMENS GRAPH5和GRAPH5 / II PLC編程包兼容，因此它還需要標準的SIEMENS功能和步驟塊（FB70 / 71-SB0，F(xiàn)B72-SB2，F(xiàn)B73-SB3）。與實際步驟序列同時，在單獨的窗口中顯示所選步驟或轉換的邏輯?？梢栽谔菪螆D邏輯（LAD），控制系統流程圖（CSF）或語句列表（STL）中顯示和編輯此邏輯。邏輯窗口的大小可以調整。相應的符號庫也可以同時顯示和編輯。步驟框的大小可調整為所用注釋的大?。啃凶址麛?shù)，行數）。狀態顯示與編輯器窗口的布局相同。特別指出活動和損壞的步驟。
Windows®S5提供了用于創建，修改，測試和記錄可編程邏輯控制器（PLC）程序的工具。Windows®S5 專為使用STEP5 對Siemens PLC系列 SIMATIC S5 進行編程而設計。功能塊圖（FBD），梯形圖（LAD）和語句列表（STL）用作S5的演示?，F(xiàn)有的S5 程序可以不使用im- / export進行直接編輯。Windows®的S5與原始的Siemens編程單元兼容。為了自動進行故障排除，還集成了S5 Doctor功能。
一個舒適的編輯器創建和編輯符號表已集成?？梢运阉骱吞鎿Q任何標準以及重新布線。語法檢查已集成。新的舒適的多段編輯器用于創建語句列表，功能塊圖和梯形圖，也可以表示復雜的功能。重點放在鼠標和/或鍵盤的易用性上。交叉引用和/或相應的符號文件以正確的地址顯示。在此窗口中，可以同時編輯符號文件。集成了帶有語法檢查的地址分配。報表列表是在集成的編輯器的幫助下創建的。Windows剪貼板可以在任何地方用于程序或配置操作。語句列表可以更改為功能框圖或梯形圖，只要它們可以顯示。始終可以以狀態語句列表的形式顯示功能框圖和梯形圖。
所述OsciCAM ®允許通過的先前記錄的視頻和處理信號的同步來分析運動的過程。記錄的視頻可與過程信號同步顯示，并帶有時間戳顯示PLC的已記錄塊狀態。
使用Statusrecorder可以通過隨后逐幀分析塊狀態來探索動態過程。Statusrecorder記錄塊狀態，并用時間戳顯示這些狀態，從而允許在顯示STL，CSF和LAD之間進行后續更改。
Statusrecorder PLC塊狀態
狀態記錄器增值稅
使用示波器編程系統的診斷功能得到了進一步增強。動態過程可以在集成的屏幕中進行監視和分析，其外觀和感覺可以從示波器前面板進行調整。使用虛擬測試探針指向I / O信號足以監視虛擬示波器內部的多個信號?？梢噪S時停止信號記錄，以進一步檢查機器故障的時間。除了監視I / O信號外，還可以通過在塊狀態下使用測試探針簡單地指向變量來監視程序執行的定義位置處的局部變量的狀態。只有集成到用于Windows®的編程系統S5中，才可以實現此目的。記錄的數據也可以保存以供以后調查，存檔或通過電子郵件發送信息。
示波器功能
使用Windows®的S5，可以在狀態顯示表示語句列表，功能塊圖和梯形圖中顯示多個段。CPU狀態功能提供有關中斷堆棧，塊堆棧和系統數據的信息。
Windows®S5允許調用COM軟件包?？梢酝ㄟ^USB適配器建立與PLC的通信。
適用于Windows® 步驟序列編程的G5（現在已包含在Windows®的S5中）是一種工具，用于在STEP5 PLC程序中輕松編程順序步驟（順序控制）。在步驟序列塊（SB）中編程的步驟序列是由步驟和轉換組成的。轉換邏輯用于啟用以下步驟。用于Windows®步驟序列編程的圖形G5支持線性序列，替代分支，同時分支和跳轉。步驟顯示在方框中。在初始步驟，步驟和選擇步驟之間有區別。初始步驟用于無條件啟動步驟序列。即使步驟標志未激活，也將始終執行步驟的指令。如果步驟標志未激活，則選擇步驟的指令將跳過。轉換顯示為行。僅當轉換邏輯為真時，才執行以下步驟。通過同時分支，可以分支多達八（8）個其他步驟。步驟和過渡的圖形顯示可能包含注釋。除初始步驟外，每個步驟都可以分配一個時間。這可以是等待時間（延遲計時器）或監視時間（看門狗）。 用于Windows® 圖形步驟序列編程的G5 與SIEMENS GRAPH5和GRAPH5 / II PLC兼容編程包，因此它也需要標準的西門子功能塊和步驟塊（FB70 / 71-SB0，F(xiàn)B72-SB2，F(xiàn)B73-SB3）。與實際步驟序列同時，在單獨的窗口中顯示所選步驟或轉換的邏輯?？梢栽谔菪螆D邏輯（LAD），控制系統流程圖（CSF）或語句列表（STL）中顯示和編輯此邏輯。邏輯窗口的大小可以調整。相應的符號庫也可以同時顯示和編輯。步驟框的大小可調整為所用注釋的大小（每行字符數，行數）。狀態顯示與編輯器窗口的布局相同。特別指出活動和損壞的步驟。
