進入公司商鋪

Electric welding machine cable product description:

本產品適用于對地電壓交流不超過200V和脈動直流峰值400V電焊機用二次側接線及連接電焊鉗.是適用于電焊機二次側接線及連接電焊鉗的電纜,額定電壓交流不超過200V和脈動直流峰值400V。結構為單線芯,采用多股軟導線復絞制成。導電線芯外面采用耐熱聚酯薄膜絕緣帶繞包,zui外層用橡皮制成的絕緣兼護套做為保護層。YH電焊機電纜

This product is suitable for AC voltage not exceeding 200V and 400V peak pulse current welding two side connecting line and electrode holder. Is applicable to the welding machine wiring two side and special cable connection welder, AC rated voltage not exceeding 200V and 400V peak pulse current. For a single core structure, a multi unit made of soft wire cutter. Conductive wire core outside the use of heat-resistant polyester film insulation tape wrapped around, the outermost layer made of rubber insulation and sheath as protective layer.YH電焊機電纜

表6-9-14電焊機電纜型號

Table 6-9-14 welding machine cable model，

型號 名稱

Type name

YH 天然膠護套電焊機電纜

YH natural rubber sheath welder cable

YHF 氯丁或其它相當?shù)暮铣赡z彈性體護套電焊機電纜

YHF neoprene or other equivalent synthetic elastomer sheath electric welding cable

的使用要求：

Use requirements of YH electric welding machine cable:

(1)YH電纜是在低電壓(zui高電壓為200V)大電流的條件下工作,要求具有一定耐性。

(1) YH cable is working at low voltage (maximum voltage of 200V) under high current conditions, requiring a certain degree of tolerance.

(2)焊把線電纜*允許工作溫度不應超過65℃。

(2) long allowed working temperature of welding wire cable shall not exceed 65 DEG C.

(3)電機引接線電纜頻繁地移動，扭繞和施放,要求柔軟,彎曲性能好。

(3) motor wiring cables frequently move, twist around and cast, requiring soft, good bending performance.

(4)在施放中易受到尖銳鋼鐵構件的刮、擦,故要求電纜絕緣抗撕、耐磨等機械性能好。

(4) in the casting vulnerable to sharp steel components scraping, cleaning, so the cable insulation tear, wear and other mechanical properties are good.

(5)使用環境條件復雜,如日曬、水沸、接觸泥水、機油、酸堿液體等,要求有一定的耐氣候性和耐油、耐溶劑性。

(5) the use of complex environmental conditions, such as sun, water boil, contact mud water, oil, acid and alkali liquid, require a certain weather resistance and oil resistance, solvent resistance.

(6)有時會碰到熱焊件,要求耐熱變形性好。

(6) sometimes encountered hot weldment, requiring good thermal deformation.

(7)經常移動,要求外徑小,重量輕。由于對此種電纜電性能要求不高,且使用環境條件復雜,在結構上要求滿足各種復雜的環境因素是不適宜的。使用時注意改善使用條件,防止外來破壞。

(7) frequent movement requiring small external diameter and light weight. Because of the low demand for the electrical performance of the cable and the complicated use of the environment, it is not suitable to meet various complicated environmental factors in the structure. When used to improve the use of conditions to prevent foreign damage.

電焊機電纜[1]（YH電纜）全稱高強度橡套電焊機電纜，俗稱焊把線，是YC電纜（通用橡套電纜）的一種。用于電焊機二次側接線及連接電焊鉗、電焊機的電纜，其特性是電阻大、電壓低。工作電壓一般為450V到750V。

Electric welding machine cable [1] (YH cable) full of high strength rubber sleeve electric welding cable, commonly known as welding wire, is a YC cable (general rubber cable). For the electric welding machine two secondary side wiring and electrode holder, welding connection cable, its characteristic is high, low voltage resistance. Operating voltage is generally 450V to 750V.

電焊機電纜的結構為單線芯，一般為多跟銅絲組成銅絲組，多組銅絲組則組成電焊機電纜的導體部分，所以YH電纜線體較粗，銅絲數百根。多組銅絲的周圍被一層耐熱聚酯薄膜絕緣包裹。絕緣層一般為*橡膠，銅絲為無氧銅，這樣，才能保證線芯的良好導電性及電纜的安全性。

The structure of electric welding machine cable for a single core, usually with copper wire conductor composed of groups, groups of copper group is composed of welding cable, so YH cable body coarse copper wire, hundreds of root. Many groups around the copper wire by a layer of heat-resistant polyester film wrapped insulation. The insulating layer is pure natural rubber, copper wire for copper, so, in order to ensure the safety of wire and cable of good conductivity.

常用電焊機電纜的規格型號有16平方、25平方、35平方、50平方、70平方、95平方、120平方等。

Commonly used electric welding cable specification model has 16 square, 25 square, square, 50 square, 35 square, 70 square, square, 120 square.

電焊機電纜的幾個特性：

Several characteristics of electric welding machine cable:

(1)YH電纜是在低電壓(zui高電壓為200V)大電流的條件下工作,要求具有一定耐性。

(1) YH cable is working at low voltage (maximum voltage of 200V) under high current conditions, requiring a certain degree of tolerance.

(2)焊把線電纜*允許工作溫度不應超過65℃。

(2) long allowed working temperature of welding wire cable shall not exceed 65 DEG C.

(3)電機引接線電纜頻繁地移動，扭繞和施放,要求柔軟,彎曲性能好。

(3) motor wiring cables frequently move, twist around and cast, requiring soft, good bending performance.

(4)在施放中易受到尖銳鋼鐵構件的刮、擦,故要求電纜絕緣抗撕、耐磨等機械性能好。

(4) in the casting vulnerable to sharp steel components scraping, cleaning, so the cable insulation tear, wear and other mechanical properties are good.

(5)使用環境條件復雜,如日曬、水沸、接觸泥水、機油、酸堿液體等,要求有一定的耐氣候性和耐油、耐溶劑性。

(5) the use of complex environmental conditions, such as sun, water boil, contact mud water, oil, acid and alkali liquid, require a certain weather resistance and oil resistance, solvent resistance.

(6)有時會碰到熱焊件,要求耐熱變形性好。

(6) sometimes encountered hot weldment, requiring good thermal deformation.

(7)經常移動,要求外徑小,重量輕。由于對此種電纜電性能要求不高,且使用環境條件復雜,在結構上要求滿足各種復雜的環境因素是不適宜的。使用時注意改善使用條件,防止外來破壞。

(7) frequent movement requiring small external diameter and light weight. Because of the low demand for the electrical performance of the cable and the complicated use of the environment, it is not suitable to meet various complicated environmental factors in the structure. When used to improve the use of conditions to prevent foreign damage.

電焊機電纜使用與維修

Electric welding machine cable use and maintenance

1、本裝置為不可維修型，其各項保護特性由制造廠規定，不可隨意調整。如有異常與本公司；

1, the device is not maintenance type, its protection characteristics by the manufacturer, not optional adjustment. If abnormal contact with the company;

2、弧焊機有風冷及主回路有接觸器的，要將風機及接觸器線圈電源接于裝置的輸入電源端；

2, arc welding machine has air cooling and the main circuit contactor, the fan and contactor coil power supply connected to the device input power supply end;

3、每次使用前觀察保護器指示燈狀態，紅燈是電源指示，綠燈是安全電壓指示，其正常狀態

3, before each use to observe the protector indicator state, red light is power indication, green light is safe voltage indication, its normal state